Technician Utilization Calculator for Plumbers: What a 60% Week Really Costs
A plumbing shop pays a service plumber for 40 hours in a week. The tickets show 24 billable hours. The other 16 hours went somewhere, and the shop cannot fix what it cannot see. The technician utilization calculator for plumbers turns paid hours and billable hours into one number, then shows what a higher number would add over a year.
Utilization is not a grade. It is a diagnostic. A low number points at drive time, callbacks, parts runs, or idle gaps, and each of those has a different fix. This guide works through one plumber’s week with the free technician utilization calculator for plumbers, so you can see the math, the breakdown, and the decision it leads to.
What the calculator asks for
The technician utilization calculator for plumbers takes four inputs, all from the shop’s own records:
- Paid hours per week: everything you pay the technician for, including drive time, callbacks, training, and waiting for the next job.
- Billable hours per week: hours invoiced to a customer. Wrench time on site counts. Drive time, uninvoiced callbacks, training, and idle time do not.
- Where it goes (optional): a breakdown of the non-billable hours into drive, callbacks, parts runs, paperwork and training, and idle time. This is a diagnostic aid. It reconciles against the non-billable total but does not change the utilization calculation.
- Target utilization: a realistic step above where the technician is now, set from the shop’s own history. The technician utilization calculator for plumbers shows the extra billable hours per year that target would add, only when the target sits above the current figure.
No benchmark ranges are built into the tool, and none are used here. The tool page is clear on this point: utilization moves with service mix, territory, and season, so compare a technician against their own history rather than against other trades or other shops.
A service plumber’s week, worked through
Take one service plumber on a standard week. The numbers below are illustrative, so you can follow the math and then substitute your own.
The dispatcher enters: 40 paid hours, 24 billable hours, and a target of 70%.
| Figure | Calculation | Result |
|---|---|---|
| Billable utilization | 24 ÷ 40 × 100 | 60% |
| Non-billable hours per week | 40 − 24 | 16 hours |
| Billable hours per year | 24 × 52 | 1,248 hours |
| Non-billable hours per year | 16 × 52 | 832 hours |
| Extra billable hours per year at 70% target | (0.70 − 0.60) × 40 × 52 | 208 hours |
Sixty percent means 24 of every 40 paid hours reach a customer invoice. The other 16 hours are paid time that produces no ticket. Over a year that is 832 non-billable hours, against 1,248 billable ones. The gap is the story of the week, and the breakdown in the next section is where it gets specific.

What a 70% target would add
Closing the gap from 60% to 70% adds 208 billable hours a year. To put a dollar figure on that, use the shop’s own loaded hourly rate. At an illustrative $140 an hour, 208 hours is $29,120 a year. That $140 is an assumption for this example only, not a tool input. If your loaded rate is different, the hours still stand and the dollars follow your rate. The fully-loaded labour rate calculator gives you that rate from wages, burden, and overhead if you do not have it yet.
Smaller steps add up too. One extra billable hour a day, five a week, takes this plumber from 24 to 29 billable hours: 29 ÷ 40 × 100 = 72.5% utilization. That is 260 extra billable hours a year, or $36,400 at the same illustrative $140 an hour. A target only works if it is reachable from where this technician actually is. Pick a realistic step above the current figure, close it, then set the next one.
Where the 16 non-billable hours go
The calculator’s optional breakdown splits the 16 non-billable hours into the kinds of lost time a plumbing shop actually sees:
| Where the time goes | Hours per week | What it looks like |
|---|---|---|
| Drive between calls | 6 | Cross-town runs between scattered tickets |
| Uninvoiced callbacks | 3 | Return visits on warranty work you cannot bill |
| Parts runs to the supply house | 3 | Mid-day trips for fittings not on the truck |
| Paperwork and training | 2 | Tickets, photos, and product updates |
| Idle, waiting for the next job | 2 | Gaps between dispatched calls |
| Total | 16 | Reconciles exactly to the non-billable total |
Drive time is the biggest bucket at 6 hours, and it is also the most fixable from the dispatch board. Batching calls by area and sending the nearest available plumber cuts it without touching the work itself. Parts runs at 3 hours point at truck stock: the common fittings for the week’s jobs should be on the van before the first call. Callbacks at 3 hours point at first-time fix rate, and they deserve their own tracking, since a callback that cannot be invoiced is pure cost. Idle time at 2 hours is the gap filler: small jobs, quotes, and maintenance visits that fit between full calls.
A peak week and a slow week
One week does not define a shop. Utilization moves with the season, so check the same technician across different weeks before drawing a conclusion.
A peak week with 31 billable hours runs at 77.5% utilization: 31 ÷ 40 × 100. Non-billable time drops to 9 hours a week, or 468 hours a year at that pace. A slow week with 20 billable hours runs at 50%: 20 ÷ 40 × 100. Against the 70% target, that slow week is a shortfall of (0.70 − 0.50) × 40 × 52 = 416 hours a year if it ran all year, which it does not. The point is the range. A shop that only looks at peak weeks will set a target nobody can hold in February, and a shop that only looks at slow weeks will leave money on the table in July.
Two input mistakes that distort the number
Wrong inputs make the number lie, and both of these are easy to make.
Counting drive time as billable. If the 6 drive hours are counted as billable, the apparent figure becomes (24 + 6) ÷ 40 × 100 = 75%, against a true 60%. The shop looks efficient on paper while the truck is still burning the same hours. Drive time between calls is paid time, not invoiced time, and the technician utilization calculator for plumbers is explicit that it does not count.
Folding overtime into paid hours. If the same plumber works 4 hours of overtime, paid hours become 44 while billable hours stay at 24. The calculation gives 24 ÷ 44 × 100 = 54.5%, which understates the normal week. Overtime belongs in its own view, not mixed into the standard-week denominator. Keep paid hours at the regular scheduled week when you compare week to week.
What to fix first
Start with the biggest bucket that has a fix you control. For this plumber, that is drive time at 6 hours a week. Batch tickets by area, keep the board tight, and send the nearest plumber to each call. Next, parts runs at 3 hours: restock the van for the common jobs and check stock before the first call, not after the plumber is already on site.
Then callbacks at 3 hours: track which jobs come back, and treat a repeat visit as a quality signal, not just lost time. Idle time is last, because it shrinks on its own once the board is tighter. Rerun the technician utilization calculator for plumbers after each change with the new week’s figures, and watch whether the breakdown moves, not just the headline number.
Frequently asked questions
What counts as a billable hour?
Time you invoice to a customer: the work on site that appears on the ticket. Drive time between calls, callbacks you cannot invoice, training, paperwork, and waiting for the next job are paid hours, not billable hours.
What utilization should a plumbing shop target?
Set it from your own history. Pick a realistic step above where you are now. Closing even a few points recovers real hours over a year, as the what-if line in the technician utilization calculator for plumbers shows. No benchmark ranges are published for this tool, and borrowing another shop’s number will not help.
Should I compare technicians against each other?
Only technicians with a similar service mix. A residential service plumber and a commercial install plumber will never have comparable numbers. Use utilization to diagnose routing, truck stock, and dispatch gaps, not to rank.
Does the breakdown change the utilization number?
No. The where-it-goes breakdown is a diagnostic aid. It reconciles against your non-billable total but does not change the calculation. Its job is to show you which kind of lost time to fix first.
How often should a shop recheck utilization?
Whenever rates, territory, or the season change. Rerunning the technician utilization calculator for plumbers with the new week’s figures keeps the target aligned with the current board instead of last season’s costs. A monthly check on the same technician’s numbers is enough to see a trend without chasing weekly noise.
How should a plumbing shop use this on the next board?
Run the week’s numbers for each service plumber, look at the breakdown before the headline, and pick the biggest bucket with a fix you control. A 60% week is not a verdict on the plumber. It is a map of where the paid hours go, and most of those hours are decided by dispatch, truck stock, and callback quality, not by wrench time. The missed call cost guide for plumbers covers the other side of the same board: the revenue that never reaches a technician at all.
Run your own numbers
Enter your plumber’s paid and billable hours in the free technician utilization calculator for plumbers and see the yearly capacity, the non-billable breakdown, and what a higher target would add.
Photos: Sergei Starostin and Jan Zakelj via Pexels.








